Faultless G2X2LYED0AA-F Manuel d'instructions

ELECTRONIC KEYPAD LEVER LOCKUser's Guide

8INSTALLATION INSTRUCTIONSA. Insert the latch into the latch hole. Using the faceplate as a pattern, TRACE a line along the out edge of the facep

9INSTALLATION INSTRUCTIONS4. STRIKE PLATE INSTALLATIONA. Placing the strike plate on the door frame, TRACE a line along the out edge of the strike pla

INSTALLATION INSTRUCTIONS5. LEVER DIRECTION DETERMINATION NOTE: Do not install the lock when the lever is at vertical position.Before lock installatio

11INSTALLATION INSTRUCTIONSNOTE: Do not install the lock when the lever is at vertical position.Before lock installation, please determine the outside

12ButtonINSTALLATION INSTRUCTIONS6-1. TO RESET DIRECTION OF INSIDE LEVERPress the button below ''SWITCH'' mark of the interior ass

13INSTALLATION INSTRUCTIONS6-2. TO RESET DIRECTION OF OUTSIDE LEVER Use a screwdriver to press the button in the hole below ''SWITCH'&a

CableINSTALLATION INSTRUCTIONS147-1. MOUNTING EXTERIOR ASSEMBLYA. Slide the spindle and screw posts through the latch and thread the cable under the l

15INSTALLATION INSTRUCTIONSA. Remove battery pack cover by pushing it up to the top position.B. Remove the lever by inserting the catch tool into the

16INSTALLATION INSTRUCTIONS7-3. REMOVING DECORATIVE COVERA. Remove decorative cover by holding fingers at cover's edges as shown in photo A.B. Us

Interior assemblyBlue wire17INSTALLATION INSTRUCTIONSA. Insert the cable into the connector port firmly with blue wire just under the red black wires

WARNINGCAUTION !1IMPORTANT SAFETY INSTRUCTION1. To prevent damage to the finish, DO NOT use any abrasives, sharp objects or harsh chemical

18INSTALLATION INSTRUCTIONS7-5. BATTERY INSTALLATIONA. Snap the decorative cover back onto the interior assembly.B. Place four alkaline batteries into

19INSTALLATION INSTRUCTIONS7-6. REINSTALL LEVERReinstall the lever after the decorative cover is snapped back onto the interior assembly.NOTE: If you

INSTALLATION INSTRUCTIONS20For lever removal and assembly process, please see page 21-25.8-1. EXCHANGE OF LEVER

21Catch toolINSTALLATION INSTRUCTIONS8-2. EXCHANGE OF LEVER (REMOVAL OF INSIDE LEVER)Insert the catch tool into the access hole on the lever. Once the

22INSTALLATION INSTRUCTIONSA. Insert the key horizontally and turn counter-clockwise 90 degrees. B. Insert the catch tool into the access hole on the

23INSTALLATION INSTRUCTIONSABCD8-4. SWAP INSIDE AND OUTSIDE LEVERS (REMOVAL OF CYLINDER)A. With lever removed, withdraw the key.B. Slide the cylinder

24INSTALLATION INSTRUCTIONS8-5. SWAP INSIDE AND OUTSIDE LEVERS (ASSEMBLE OUTSIDE LEVER)A. Turn the key counter-clockwise by 90 degree to vertical pos

25INSTALLATION INSTRUCTIONS8-6. SWAP INSIDE AND OUTSIDE LEVERS (ASSEMBLE INSIDE LEVER)Align inside lever and push it back to slide onto spindle until

217.Low Battery Indicator261.Indicator2.Keypad3.Cancel Button5.Key Override4.Confirm Button6.Thumbturn(Auto-Locked/Unlocked switch)MAIN OPERATING INST

27MAIN OPERATING INSTRUCTIONS

CONTENTSINSTALLATION INSTRUCTIONS 1. COMPONENTS 3. LATCH INSTALLATION 4. STRIKE PLATE INSTALLATION 5. LEVER DIRECTION DET

28SETUP MODE1. CHANGE PROGRAMMING CODE ( )(1) The pre-set programming code of the product is 123456, please change it before operating the loc

292. ADD A USER CODE (MAXIMUM 100 SETS USER CODES WITH 4-8 DIGITS IN LENGTH.)Procedures:(1) Rotate the internal thumbturn to horizontal position pre

304. DELETE ALL THE EXISTING USER CODES AT ONCEProcedures(1) Rotate the internal thumbturn to horizontal position press # (the red indicator is on,

316.DISABLE BUTTON SOUND (MUTE MODE)Procedures(1) Rotate the internal thumbturn to horizontal position press # (the red indicator is on, you

10-3. TO LOCKOPERATION MODEVertical (arrow) position is auto-lockedHorizontal (arrow) position is unlockedAB321. TO ACTIVATE AUTO-LOCKING (AUTOMATIC R

33OPERATION MODE2. TO OPEN (UNLOCK) THE DOORA. Enter the correct user code or programming code.B. Upon the green indicator light on and a short beep h

OPERATION MODE343. TO DEACTIVATE AUTO-LOCKING (AUTOMATIC RE-LOCKING)Use a flat tool to turn the slotted turn on the inside as shown from vertical posi

A. Keypad does not respondB. Can not change programming codeC. Can not delete all the existing user codes at once1. Check to see if the batteries

E. Can not open the door after input a correct user codeF. Yellow indicator is on or keeps flashing1. Make sure you have entered the correct u

37PROGRAMMINGCODENAME CODESECURITY INSTRUCTIONS1. Do not share your programming code with anyone else.2. Keep a written copy of all valid user codes i

CONTENTSMAIN OPERATING INSTRUCTIONSSETUP MODE 1. CHANGE PROGRAMMING CODE 2. ADD A USER CODE 3. DELETE INDIVIDUAL EXISTING USER COD

This device complies with Part 15 of the FCC. Operation is subject to the following two conditions:(1) this device may not cause harmful interference,

This Class B digital apparatus complies with Canadian ICES-003 .Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.This d

Rev. 12/05-00 G36-L000012

4ABCDEFGHIJKLMINSTALLATION INSTRUCTIONSA. KeyB. Exterior AssemblyC. Mounting PlateD. Interior AssemblyE. Decorative CoverF. Battery Pack CoverG. Lever

5Fold herePlace on door edge51 45 40 35Drill 1''(25mm) hole at center of door edge2''1-3/4''1-9/16''1-3/8&apos

654mm(2-1/8'')25mm(1'')60mm(2-3/8'') or 70mm(2-3/4'')A BDOOR PREPARATION2. DOOR PREPARATIONUse Diagram of spad

760mm(2-3/8'')70mm(2-3/4'')INSTALLATION INSTRUCTIONS3. LATCH INSTALLATIONA. Pull the drive-shaft backward for adjustment to 70mm(2